Friday, March 14, 2014

Frosty Drives Mono

Frosty@Spring Mountain Motor Resort

Jonathan Frost, Skip Barber Instructor and SMMR Stingray Coach, had a chance to drive the BAC Mono last weekend.  He is an experienced professional racer with experience in many cars.  'Frosty' has also driven the various Palatov cars and will be one of the pros that will be helping us with Project Dragon.  Here are his comments after driving the Mono:
Driving the Mono was better than I ever expected. Having driven many low production track special cars i.e. caterham 7's, Elise's, Atoms, Radicals and even track modified streetcars. They always tend to be a little bit quirky. The performance is always there, but generally they fall short here and there. Not that I can fault the little guys, but when you hold them against the likes of Porsche and Ferrari that have had 60+ years to get it right, they can't compete in fit and finish and overall completeness. 
 The Mono is like nothing I have experienced before. I can honestly say that the Mono meets the Goliaths at their level. Fit and finish is exquisite. The car has zero bad habits. Heading out on track I expected to find a car that was nervous, edgy.  A car I'd have to watch my back around much like the formula cars I used to race.
 Boy, was I wrong. The Mono has the refinement and a personality much like the exotic club sport specials. (GT3's, Scuds, Caman R's)
 
 My first lap in the Mono I immediately felt at home. The car instantly became an extension of my driving suit.  Completely intuitive, everything I wanted the car to do, it did with flying colors.  On my second lap, I was able to lap the Spring Mountain East course fast enough to catch and pass a Radical SR3.  The car is blisteringly quick around the track. 
If I had any complaint, it would be that car is so well behaved that you don't feel like you're going that fast. It's that good.  The car sends the driver so much feedback that even a casual enthusiast will be able to extract much of the potential this car has to offer.  I'm in love!
To quote Ferris Bueller:  "I love driving it, it is so choice. If you have the means, I highly recommend picking one up"

We are looking forward to bringing the Mono to Laguna Seca and letting him drive it.  Watch Frosty drive an early D2 test mule at Laguna Seca:



Tuesday, March 4, 2014

The Importance of Track Checklists

Trackdays are a great way to properly exercise our cars and an activity that many of us enjoy.  Ensuring that our cars run well, without mechanical problems, generally comes down to preparation before the event AND during the event.  In the last several years, we've come to adopt a more 'race-like' approach to our trackdays.  This entry discusses and provides Checklists that we have used to keep our cars running well.

Racing has taught us that Checklists are key to reliable running.  Anyone who runs trackdays -  racing or not - will also benefit from the use of Checklists.  Our participation in Lotus Cup and now with our Spec:Race Atom series has given us a perfect opportunity to use these Checklists effectively.  

Here are ones that we use (click link to see each list):
  1. Initial Checklist
  2. Post Practice Checklist
  3. Track Checklist
  4. Set Up/ Set Down Checklist
Aggressively run cars - especially with slicks need frequent wheel bolt torque inspection


A clipboard is an effective tool to organize and use your Checklists.  For racing we follow a strict sequence and use these Checklists as follows:

Sheltered workspace is ideal - bring an EZ-Up!
Pre Race Day
  • Set Up Checklist
  • Initial Checklist
Practice 1
  • Post Practice Checklist
  • Track Checklist
Tire temps & pressures in the Hot Pit
Practice 2
  • Post Practice Checklist
  • Track Checklist
Practice 3
  • Post Practise Checklist
  • Track Checklist
Practice 4/Qualifying
  • Post Practice Checklist
  • Track Checklist
Race
  • Post Practice Checklist
  • Track Checklist

We'd suggest you tweak these lists and sequence to fit your needs.  You'll notice they include things like data acquisition downloads and driver support oriented tasks.  We try to list everything so our grey matter is not taxed anymore than necessary.  Minimizing the amount of things that you have to remember becomes of the key advantages of these lists.  

Regardless of your skill level, routine inspection should be a requisite part of your track day activities.  If you don't have the ability to do the work yourself, considering hiring a capable shop or mechanic to do the work for you.  Nothing is worse than losing a track weekend because you forgot to tighten a bolt, check fluid levels or inspect your brakes.  A bit of preventative maintenance will go along way to ensuring you have a great weekend.

Clean cars win races!




Saturday, February 15, 2014

Project Dragon Update: Intro and More


CONCEPT:
Project Dragon is the new car that we are planning to introduce later this year for both road and track use.  The 1800lb car will feature a 430hp V8 engine and 6spd syncro gearbox.  Our goal is to build a car with excellent performance, safety and reliability.  This car will be a pure drivers car with no electronic driver's aids.  Frankly we prefer cars that require our active involvement in driving.  We know that we can never compete with the likes of Chevrolet, Ferrari, Porsche, etc when it comes to technology.  So we have chosen to go in the opposite direction.  I've been calling this car the 'Luddite' as a result.  It really is the antithesis of the modern supercar.  We are not technophobes, in fact we love technology, especially this one, or this one and even this version.  We simply believe there are many driving enthusiasts who are looking for simpler sportscars that keep you engaged in the art of driving.  A perfectly rev-matched downshift is truly a thing of beauty...

We are working with Palatov Motorsport with a chassis that they have engineered.  Their car is known as the D2 and we are effectively designing a variant.  Ultimately we believe we can develop alternative bodies that clients can interchange onto this existing chassis.  We will offer the D2 for sale here in CA and have ordered a D2 body for our first test mule.  Our car will feature different cosmetics as well other technical differences including, suspension, brakes, trans and more.  I'm viewing Project Dragon much like the BRZ/FRS, Camaro/Firebird or other cars that share a platform and have varied levels of difference.  We will offer a windshield for those clients that want more protection and/or required for registration.



We've recruited a couple of good friends and engineers to help us with the technical validation of Project Dragon.   Ryan Kuhlenbeck will help with the mechanical integration and electrical systems.  This man's hobby is creating world-class wiring harnesses using OE connectors and methods.  He will take the supplied harness from GM and make them into things of beauty and most importantly, benchmarks of reliability. Dave Thilenius will be our man behind the wheel to help us with Ride & Handling along with pushing the car hard enough to see how it fares in severe track use.  Both of these gents (I do use that term loosely), have done much work at Sector111 and have been instrumental in the success and quality of many of our products.  

Additionally, Bill Thomas, from William Thomas Roadsters, is on board as our point man on the East Coast.  Bill's technical knowledge and expertise with light cars will be a great boon to our development.  Plus he can drive fast and will put our test mule through the paces on East Coast tracks this Spring.  Bill is especially pleased with our choice of MV as a design inspiration!  I've also got Jonathan Frost (Skip Barber Coach) queued up to do some test driving as he has driven the D2 on track and is currently coaching Stingray clients at SMMR.

DESIGN:
We decided to do a very elemental body to start as the D2 already features a full body.  Additionally a simple body would not consume all of our limited resources.  To this end, we hired several designers from around the world to submit sketches to us.  We received several great renderings that ran the gamut of full bodies to more partially 'clothed' styles.  My love for the Atom was another reason to create a car that would be elemental.  There is nothing like blasting around in a semi-open sportscar!


We have now chosen one design that we are planning on producing.  The design meets my critical eye and will fit with the ethos of our car - especially at this stage.  I'm confident it will age well and not be viewed as too trendy in the coming years.  No new design ground will be broken, but the car will still be polarizing and aggressive.  Details and finishing are important to the over look and feel of this car.  These are still in-progress as the design still needs refinement.  We plan to use hardware and fasteners that will be exposed but look appropriate and fit with our aesthetic.  Expect a full front and rear wing kit for downforce and an added dose of aggression.  Our long time clients know about the design/technical innovations that we've implemented in the Lotus market, expect a few interesting things as well with Project Dragon.


POWERTRAIN:

The venerable LS engine is a reliable, powerful and cost effective engine.  GM introduced the eRod version of the LS3 for hot rodders and kit car manufacturers that were looking for a 50 state emissions compliant engine.  This lightweight crate motor comes with a factory ECU, catalytic converters, header, e-pedal, OBDII port, wiring harness AND a 24month/50k mile warranty.  Smog compliance plus the windshield will allow us to offer a special construction car (AKA kit) that can be registered in most US states and Canada.

The driving feeling delivered by 424lb-ft of torque coupled to 1800lbs will be completely different from the high revving motors we are used to in our Lotus/Ariel/BAC cars.  The ability to leave the car in a higher gear and have it pull from the corner will ultimately allow the driver to shift less gears and stay focused on his braking points, turn-ins, apexes and exits.  Over twenty years ago I owned a Yamaha FZR400 which revved to the moon.  It was a great bike and I loved ringing that engine out - it made no real power down low.  At the time I test rode a Ducati 900 Supersport and was immediately taken by the added torque and the ease of accelerating out of the corners.  That Ducati revved much lower with a very torquey engine and was lightweight.  Well soon thereafter, I bought a Duck and came to like both styles of power delivery - and the required change in riding/driving styles.  The Dragon works in the same way as  the Ducati when compared to the other light cars we adore.  Variety is the spice of (driving) life.  8^)


The transaxle that has been run in the D2 is a 5spd gearbox from a Porsche 911 (964version) and is a durable solution.  It has seen over 25 days of track use in the D2 test mule (see above).  This will be the base trans that we will offer.  Of course, we convinced ourselves that an even more righteous trans should be tested because we are lunatic track drivers.  The Porsche 997 GT2 6spd trans became the object of our attention.  This syncro box is available with a factory LSD, internal oiling and stronger syncros.  It is an expensive solution but one that we think will deliver higher levels of durability for the track day junkies that we hope to attract with this car.

OTHER COMPONENTS:

We know that this car will be driven on the street and track.  The choices we are making for various components will take these intended uses into consideration.

Cosworth's latest dash technology has been selected for our car.  It has a fully configurable display with multiple screens.  This allows the user to toggle between a road screen and a track screen.  I tend to favor round gauges and have difficulty reading purely digital screens - I still like to see needles sweeping.  See the picture of the digital gauge with a needle. Shift lights have really become a boon to my track day driving and this dash has lights and a great rpm sweep that changes color.  A key criteria is the size - just right.  This dash gives us all the options we can hope for and offers optional data logging.  We've ordered one with all the bells and whistles to aid our technical validation of the car and log the ample data streamed via the eRod ECU.  We are planning on keeping the interior of the car, including the switch gear, very simple.  This Cossie dash will allow us to achieve that goal.

At the PRI show I met up with my friends at Schroth USA (HMS Motorsport).  Joe Marko, owner of HMS, is planning on visiting us to scrutinize the restraints in the car to ensure that we've routed everything correctly.  Joe turned me onto a cutting-edge, Schroth, 9pt racing harness - it will be something that we will likely offer.  Yes, you read that correctly, 9points!  I'll feature it in a later blog once we have it sorted.  He will also be reviewing a modular seat padding system that will allow us to custom fit a broad range of drivers into this car.  The car has a 18" wide seat so wide drivers will fit along with tall guys - we got 6ft5" Ryan into a D2 last year.

We are working with other companies to develop optional exhaust, wheel, suspension, brakes and more.  Expect some tasty upgrades to become available.

Our test mule chassis is nearly completed.  Palatov will be creating a new rear subframe to accomodate the GT2 trans.  We hope to have a running mule in March and will run her at SMMR soon thereafter...

Thursday, February 13, 2014

CEL on our Exige 'S' (DTC P0101 Troubleshooting)

After a spirited mountain run, our test Exige, 'Switchblade', threw a CEL (Check Engine Light). The scanner told us we were getting 'P0101' which translates to "Mass or Volume Air Flow Circuit Range/Performance". This means that there is an issue regarding the readings between the MAF (Mass Air Flow) sensor and the MAP (Manifold Absolute Pressure) sensor. The probable culprits? A dirty MAF, MAP, or leak somewhere in the intake system.

Let's try some simple tests/ fixes. First; we cleaned out the MAF by removing it from the air filter box and giving it a good cleaning using a MAF/MAP cleaner. This spray is available at the local auto parts store. We also cleaned off the MAP using the same stuff.  

WARNING: DO NOT USE ANYTHING ELSE OTHER THEN THE MAF/MAP SPRAY! 

You can run the risk of damaging the sensitive wires in the sensor and then you'll be left with having to buy new parts.

That first test didn't stop our code from coming back, so the next thing we did was search for vaccum leaks.  We grabbed a few cans of brake cleaner and sprayed the intake components of the engine while another tech kept an eye on the tachometer. We knew we found the leak when the RPM's started to climb after soaking the elbow that attaches to the supercharger.

We let the car cool off before diving in and taking things apart. There is a O-ring seal between the supercharger and the outlet elbow that has been an issue on a certain number of these factory-supercharged cars. Sometimes the rubber seal rips, sometimes it shrinks... either way, it's causing a boost leak. No Bueno.

If you've found an intake leak at this connection, you can follow these steps. Begin by disconnecting the MAP harness from the MAP sensor on the intercooler. Un-secure and remove the intercooler pipes. A good way to remove these pipes is to slide the rubber cup-link back to give you more space to pull them out - especially if you may have one of our BLADE kits installed.

Next, disconnect all of the ducting from the intercooler. Unbolt the intercooler, carefully remove it, and set it aside for inspection and cleaning. For those of you using any of our BLADE kits, remove the lower heat shield as this will be in your way.  With everything removed, you can now see the outlet elbow that sits on top of the supercharger held on with four 10mm bolts.

 


Unbolt the elbow and pop the elbow off. There should be little resistance so it should come off by hand. A light tap with a rubber mallet will break it loose if it is giving you a little fuss coming off.

WARNING: BE SURE NOT TO DROP ANYTHING INTO THE SUPERCHARGER WHEN REMOVING THE ELBOW!

The seal may be stuck to the elbow when removing it from the supercharger (as is shown in the photo below), so stay vigilant as not to allow it to fall into the blower. You will want to clean off the surface of the blower by spraying some brake cleaner onto a red rag or blue shop towel.



Use some blue painters tape to cover the hole when you are done cleaning the surface of the supercharger to keep foreign objects from falling in.  Clean off the surface of the elbow and inspect for any signs of major damage. There may be a little pitting on the surface -this is OK as they come this way from the casting process.


Replace the old o-ring with the new one and bolt the elbow back onto the supercharger. Make sure to torque the elbow down to 18 ft-lbs. using some blue Loctite. Don't forget to re-install the actuator bracket back on before torquing the 10mm elbow bolts to spec as well. When you are finished inspecting your intercooler for any debris and/or oil, begin the reverse process of re-installing all the parts.


Be sure to clear the ECU codes and test drive it for a few miles to make sure that the issue has been resolved. 

Friday, February 7, 2014

FIAtank Redux

We recently had the Art Car back in the shop for an oil service and to diagnose a wiring issue.  While it was here, the FIA tank was pulled for inspection to see if there was any degradation issues after a few years of track-only usage.  It has been installed in the car since 2011 (see here), so it was about time to see how this product was holding up.

After removing and draining the tank, we shipped it back to our friends at Fuel Safe to have them test and inspect it.  In the mean time, we gave a visual inspection to the Plug-n-Play fuel pump that was installed with the tank.  Some light debris was cleaned off the filter and all the connections were double-checked.  We opened the plastic unit to see if there was any debris in there, but it was all clean.


In a few days the tank was back in our hands with this report from Fuel Safe:

1.       Bladder surface was free of cracks, discoloration and was pliable.
2.       Foam baffling was in good shape with little discoloration, pliability was excellent.
3.       Internal check ball valves moved freely and all aluminum parts looked to have no corrosion.
4.       Outer aluminum can was in good shape with no visible cracks.


You can see one of the check ball valves at the bottom of the tank


Excellent news! We were happy to see that our parts were holding up, even in race conditions.  With a clean-bill-of-health, we re-installed the pump and the tank confident that it it should give trouble-free service for at least the next few years.

After picking up the Art Car, the owner went straight to Chuckwalla Raceway.  He set the fastest time of day against some serious Porsches.  Jack is an amazing driver and we are always glad to see him kick some asphalt!

Fuel starvation has been an issue on track for all of the Elise variants.  Our various fuel tank solutions fix the problem at the source.  Adding additional systems like fuel pots/surge tanks creates unnecessary complexities to these cars that can fail.  We recently learned of another client who had his Elise catch fire at Laguna Seca thanks to a failed surge tank.  We believe keeping things simple is the smartest approach with the Lotus - at least for those of us who prefer to drive instead of fix broken cars.    

Tuesday, January 21, 2014

Lotus immobilizer module bypass.

The Cobra-manufactured immobilizer that comes in the pre-’08 cars is a pretty handy piece of technology.  It can do interesting things such as: 
  • make your car more difficult for a thief to steal ,
  • make your battery go flat with a few days of non-use,
  • potentially prevent *you* from starting the car. 
Because of some these ‘features’, some owners will decide to bypass the immobilizer - especially dedicated trackcars. All kidding aside, it's a device that is sometimes troublesome and removing it will not disable your alarm.

The immobilizer is located behind the plastic bulkhead behind the seats.  To disable it, most people have traditionally unplugged the module and either plugged in a pre-built ‘Immobilizer Bypass’ module or created 2 small jumpers out of thin wire with some solder on the ends to flatten them out like pins.  These are installed into the farthest outside pins of the plug; #1 to #6 for the fuel pump, and #5 to #12 for the starter.




Recently, we had the Art Car back in the shop which had jumper wires.  We pulled out the bypass module that was on the car and tested it with a voltmeter to find a resistance change when the wires were wiggled.  To improve reliability, we clipped the wires on the car’s main harness just before the plug and soldered them together.  This allows us to not use the bypass module at all and eliminates a few more points of failure. 



Oh, and without the immobilizer bypass module, we’re saving 0.05lbs!


Wednesday, December 4, 2013

Lotus Clutch Delay Valve

Have you noticed a slight delay when quickly shifting your Lotus S240/S260?  A clutch delay valve is installed, by the factory, on the ‘08+ S240 & S260 models.  This little one-way restrictor is plumbed in before the clutch slave cylinder; it’s job is to limit the amount of fluid that passes through it when you release the clutch pedal.  It ‘delays’ the engagement of the flywheel and clutch to a pre-defined rate – this is not a pleasant ‘feature’ when you are driving the car aggressively!   Keeping this in a car that is track driven can increase clutch wear by constantly slipping the clutch at every shift.


You can find this delay valve with the undertray removed.  It is located on the firewall side of the engine, down low.  See it in place above.

Luckily, there is a fix – straight from Lotus.  Clutch Pipe C120Q0003F is the same shape clutch line without the delay valve built in! A great time to install this bit is to do it while you are flushing the brake fluid – the clutch and brakes share the same reservoir.  Bolt it on, bleed the clutch, and enjoy some positive clutch engagement!


Recognize that there is a trade-off...Why did Lotus fit such a device to these models?  Our guess is to protect the transmission.  This delay valve will limit the shock transmitted to the transmission by these more powerful engines.  The stock transmission durability is severely compromised as power starts to exceed 270hp.  Lotus have to deliver cars with warranties and replacing transmissions gets very costly.  Other OEs, like BMW, also employ the same trick.  If you remove your stock delay valve and run on track with slicks, expect more frequent trans rebuilds - especially if you have also added more power!

Friday, November 15, 2013

Oil Primer - What Oil Temps Could Your Track Car Sustain?

Safe oil temperature is an often debated subject among car enthusiasts.  Our cars use high rpm engines and get run on track, which result in high oil temperatures.  So what are safe levels?  This blog entry will shed some light on this sensitive issue.  

Oil is designed to lubricate the moving parts in your engine and to help cool it.  Oil is thicker (more viscous) when it is cold and when it warms up, it thins out and flows better.  This improves lubrication and cooling effects.  Of course it can get too thin and cause oil pressure to drop - which can be dangerous. Typically you want to achieve 10psi (.69 bar) of oil pressure for every 1,000rpm that you are running.  Cold oil is the cause of a fair amount of wear and tear that takes place to your engine.  
BAC Mono dash showing oil temp in deg C and oil pressure

I spoke at length with Chuck@Competitive Edge - our Motul distributor to get some more background on oil performance.  We run Motul oils, especially the 300V on all of our track driven cars.  This oil is an ester-based, full synthetic.  300V is designed to run as hot as 385degF(196degC) before it starts to degrade.  This is a shockingly high number for most of us but is backed with solid data and testing.      

The Mono has a Cosworth engine that recommends a heavier oil: 15W50 and the Lotus runs a thinner 5W40 in the Toyota 2ZZGE.  The following table shows some interesting 300V data that compare these two oil weights:

5W40 15W50 Standard
Density at 59degF(20degC) 0.86 0.868 ASTM D1298
Viscosity at 104degF (40degC)
81.8 mm2/s
122.9 mm2/s ASTM D445
 
Viscosity at 212degF (100degC)
13.6 mm2/s 18.1 mm2/s ASTM D445
Flash point 446degF (230degC) 460degF (238degC)  ASTM D92
HTHS Viscosity at      302degF(150degC) 4.1 mPa.s 5.3 mPa.s ASTMD4641




The above data came from Motul's technical reference sheets: 5W40 & 15W50   You can see that the heavier weight oil (15W50) maintains a higher viscosity as the temperatures rise yet at cold temps(50degF) it has about the same density as the lighter oil.  So the cold start performance/wear & tear will be similar and provide good performance as the temps rise.  Good low temp viscosity is a key advantage of a synthetic oil.


BAC Mono at Oulton Park

In the Mono, I am seeing temps up to 120deg C (248degF) with hard canyon use as well as on the track.  The factory suggests that 130degC (266degF) is acceptable.  An important consideration is to see how the oil pressure is managing - which at 120degC is fine.  We've not monitored pressure yet at higher oil temps.  We have submitted oil samples to a laboratory for analysis and found that it was still in good condition (though admittedly the mileage was under 1k).

Our ArtCar (Elise) ran oil temps as high as 270deg F (132degC) with acceptable oil pressures in Lotus Cup events.  See videos from Chuckwalla (see below) and Buttonwillow.  The oil temps climbed slowly over the course of a ten lap race - if we were to run an endurance event we would have likely added an oil cooler - this car lacked coolers.  The drySUMP on our Elise had a great cooling effect so we completely deleted all the oil coolers. 


  
We've experienced oil temps that have ranged up to 270+ degF (132degC) on our various cars.  Bill @Dailey Engineering had also mentioned that Vipers are consistently running oil temps well over 300degF with no issues.  Assuming that water/coolant temps and oil pressure remain safe, high oil temps seem perfectly acceptable.

So what kind of life can you get from a synthetic?  Typically with a good synthetic oil, the additive packages will begin to degrade first which then results in the oil needing to be replaced.  Even cars that are run hard on track can likely get 2,500-3000 miles of use before needing to change the oil.  Of course more frequent oil changes won't hurt.  


V6 Exige CupR at PB Racing
The advent of synthetic oils have been a serious boon to sportscar owners - especially the ones that drive their cars hard on track. Synthetic oils are a smart choice as they deliver the best balance of performance both at cold start as well as at high temperatures.  Technical data and actual race/track use with our cars suggests that oil can perform at very high temperatures.  

Tuesday, November 12, 2013

Atom Chassis Repair

We recently completed a chassis repair on an Atom3 that I wanted to share with you.  We had blogged in the past about a different Atom repair that we completed: HERE.  This car spun and suffered suspension damage along with one dent in one of the main chassis tubes.  Replacing the wishbones/uprights/etc was the easy part as they bolt on and off quickly.  The main tube was the item that would take some more care and attention.  
Powdercoat was removed from dent
Our original plan was to cut out the dented section and replace it with a new sleeved section.  Once we started thinking through the details of this task and discussed with TMI about the repair, we came to a different solution.  We hired a certified welder to fill in the dent and smooth out the tube.  This solution turned out beautifully and the client was very pleased with the repair. 


Weld material was added to dent
Weld material was smoothed out

Finished tubing after painting
Chassis damage of this variety in a Lotus would have resulted in a totaled car.  The exoskeleton chassis of the Atom is a unique design feature of the car that not only also adds safety and but makes crash damage much easier to manage - and affordable!